Calls answered 24/7 · Nationwide plumbing help (888) 538-0664
Leaks · November 10, 2026

Slab Leak Warning Signs (and What to Check First)

A slab leak is a supply or drain pipe failing beneath the concrete floor, and the floor is usually the last place it shows. The first honest test takes five minutes at the water meter with every fixture off. If the dial moves, water is leaving the system, visible or not.

7 min read Written for homeowners Updated November 10, 2026

The floor is a bad witness. Water that escapes a pipe under a slab does not surface where the pipe failed. It follows gravel and sand, then the underside of the concrete, until a footing, a vapor barrier seam, or the edge of a room stops it. A damp patch in a hallway can belong to a leak under a bathroom ten feet away.

So do not start by staring at the floor. Start at the meter.

The five-minute meter test

Everything else here is circumstantial. The meter is not. It measures flow, and a house with nothing running should show none.

  1. Shut off every use of water: faucets, dishwasher, washing machine, icemaker, humidifier, water softener, and any fixture with a drip you have learned to ignore.
  2. Shut off irrigation at the controller and at the backflow valve. It is the most common reason a meter moves in a house that looks idle.
  3. Find the meter, usually in a concrete box near the curb or a basement utility area. Lift the lid carefully; some are heavy and some hold water.
  4. Write down the reading and photograph it. Most meters have a leak indicator — a triangle or low-flow dial that spins when water passes.
  5. Wait five minutes, or fifteen if you suspect a slow leak. Do not flush or run a tap. Fill a pitcher first if you will want water.
  6. Read it again. Any movement means water is going somewhere.

A moving meter proves loss, not location, and a still one only clears the pressurized side. A drain line under the slab can fail and leak only when water runs through it, so no movement does not rule everything out. Drain leaks tend to show as a stain, a sewer smell, or water at the base of a fixture.

Separating the house from the yard

Find the main shutoff where the service line enters the house, close it fully, and repeat the check.

  • Meter stops: the loss is inside the house, downstream of that valve, which includes every pipe under the slab.
  • Meter keeps moving: the loss sits between the meter and the house — service line, hose bib, irrigation stub, pool fill. Different repair, usually easier to reach.

If the valve will not close all the way, say so when you call. A gate valve that has not turned in years often fails to seat, which makes the test inconclusive rather than negative.

Rather talk it through?One call, answered 24/7. Tell us what is happening and we will check local availability.

(888) 538-0664

Signals that carry real weight

A warm strip of floor that stays warm

Hot lines lose heat into the concrete, and the floor above reads it. The tell is a band, not a spot: warmth that follows a line across a room, or a patch warm in the same place at 7 a.m. and again at 7 p.m. Tile and vinyl transmit it clearly; carpet blurs it. Compare with the same material in another room, and check with the back of your hand. If the patch persists after the hot system has been idle for an hour, the heat is coming from below rather than from a recent shower.

Water noise when the house is quiet

At night, with the refrigerator and HVAC off, a pressurized leak can make a faint hiss or tick you hear through the floor. A clue, not proof. A fill valve or a neighbor's plumbing sounds similar.

A bill that climbs without a change in habits

Compare the same month last year, and look at gallons rather than the amount owed, since rates shift. A jump that survives a look at irrigation and houseguests is worth a meter test.

Dampness at the edge of a room

Cool, slightly damp carpet along a wall, vinyl lifted at a seam, a swelled baseboard. Water under a slab wicks up through concrete into anything porous it touches.

A musty smell with no visible source

Weak on its own. It can come from a shower pan, a wax ring, or a crawl space. Pair it with a meter test before drawing conclusions.

Look-alikes to rule out first

Before anyone cuts concrete:

  • Air handler condensate. A clogged line or cracked pan wets a closet floor or the carpet on the far side of a wall, and runs hardest in cooling season.
  • Water heater and pan. A weeping fitting, failed relief valve, or tank seam sends water into the next room.
  • Toilet wax ring or supply. Leaks only when the toilet is used, which makes it look intermittent.
  • Shower pan or grout. A pan that lost its seal leaks below the floor, sometimes into a room sharing no wall with the shower.
  • Irrigation and hose bibs. A stuck valve runs continuously and shows on the meter like an indoor leak.
  • Softener or filter. These discharge during regeneration, which can look like constant loss.
  • Pressure regulator. High pressure does not leak by itself, but it stresses joints and worsens an existing seep.

Rather talk it through?One call, answered 24/7. Tell us what is happening and we will check local availability.

(888) 538-0664

How a professional narrows the location

Detection is elimination in a sensible order. Expect some version of this, though equipment varies by company:

  1. Confirm the loss by repeating the meter test and recording it.
  2. Isolate hot from cold and indoors from outdoors with valves and gauges. A gauge on an isolated section either holds or falls, which answers plenty before any tool comes out.
  3. Listen with acoustic equipment while moving across the floor to find where the sound is loudest.
  4. Map moisture and temperature with meters and thermal imaging to shrink the search area.
  5. Confirm with a camera through a cleanout for a drain, or one small opening in the right place for a supply line.

Ask which line, roughly where, and what was ruled out before work begins.

Repair paths and what each asks of you

Four broad approaches. The right one depends on pipe material, location, and how much of the floor you are willing to lose.

  • Spot repair. Expose and replace the failed section. Least demolition, sensible only if the rest of that line is sound.
  • Section replacement. A longer run goes when failures cluster or the pipe is at the end of its life in that area.
  • Reroute. A new line runs overhead or through walls so the slab stays intact. Avoids concrete and suits finished flooring, but adds length, may soften pressure at distant fixtures, and needs insulation where it crosses unconditioned space.
  • Repipe. Widespread failures can make replacement more rational than chasing them one at a time.

Settle two things first: how the floor will be opened and restored, and who does the restoration. Plumbing and flooring are usually separate scopes. If the leak is under tile, one trade may open the slab and another finish it. Put that split in writing.

Insurance and the paper trail

Policies vary, so do not guess at yours. Insurers do consistently want evidence: when you noticed it, what you saw, the meter readings, photos, and the detection report.

  • Photograph the meter before and after each test, reading legible.
  • Photograph the damage before anything is moved or dried.
  • Ask what they need before the repair, not after. Some want to see it in place.

Ask whether the pipe repair is covered and whether access damage — concrete, flooring — is treated separately. The answers differ, and they change how you sequence the job.

Do not open the floor to see what is going on

A hole in the wrong place damages the floor and tells you nothing. Water travels. Let the meter test and a locator narrow the target, then make one opening where the evidence points.

When to stop troubleshooting and call

Call when the meter moves with every fixture and the irrigation off, when a warm patch or damp edge keeps returning after you dry it, when water stands in a room, or when it reaches a wall with outlets or a panel.

Two situations are not plumbing calls. If you smell gas, leave and call your gas utility or 911 from outside. If water is touching energized equipment, do not wade in; shut the power only if you can reach the panel without touching water.

For everything else the sequence holds: meter test, house-valve test, note what you found, describe it clearly. That is what turns a vague "something is wet" into a job someone can plan. For the diagnosis itself, leak detection and repair covers what the visit involves. If water is already spreading, emergency plumbing is the right door.

Rather talk it through?One call, answered 24/7. Tell us what is happening and we will check local availability.

(888) 538-0664

Frequently asked questions

Can a slab leak stop on its own?

No. Debris can partly block a pinhole and slow it, and a line that loses pressure stops leaking, but the pipe is still broken. The loss usually returns, often at a worse moment.

How long can I live with one?

Longer than you should, in most cases. A slow leak with no finished flooring above it is less urgent than an active leak under carpet, but every week adds moisture to the soil and the concrete. Treat a hot-water leak, or any water reaching a living space, as a same-day problem.

Will my water bill show it right away?

Usually not. Billing cycles are long and rates vary, so a small leak hides inside normal variation for a month or more. The meter test answers in a few minutes; the bill confirms later.

Does the whole floor have to come up?

Rarely. A spot repair needs an opening sized to the failure, and a reroute may need none at all in the slab. The exception is a line that has failed repeatedly along its length, where a larger replacement is the more sensible path.

Plumbing trouble?Calls answered 24/7
(888) 538-0664